CP80 PRINTER DRIVER

Enable mag stripe Enable or disable the magnetic stripe capabilities of the printer. Page 25 The duplex entry sensor detects the card and determines the position within the flipper. Page Free the heater and thermocouple wires from the heater assembly frame. Tighten the mounting screws to 8 in-lbs. After the value has been changed, press the Enter key to apply the settings and reboot the printer. Error Symptom Comments Code MS A card was lost when The card was never detected by either the attempting to read or write magnetic stripe or card input sensors.

Uploader:	Gasar
Date Added:	16 March 2007
File Size:	30.50 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	43814
Price:	Free* [*Free Regsitration Required]

If necessary, remove the index sensor from the ribbon guide by lifting it off the mounting post.

Rear Drive Roller If present, partially remove the smart card contact printsr Press up on the hopper retaining latches one on either side of the hopper and pull the hopper straight out to remove it. Loosen but do not remove the Upper Foil Drive Assembly page Unplug the magnetic head from the magnetic stripe board.

Card Data Systems

Inspect all sensor to make sure they are properly seated in their mounting locations. The following procedures serve as a rough guideline for isolating the cause of a failure. Page Finish removing the guard by freeing it from the slotted retainer: Connect the three connectors. Replacement printheads for use in datacard desktop card printers 2 pages.

During replacement, make sure to line up the shaft flats. Replacement Procedure Place the pick roller in the transport chassis. prinnter

Print several test cards to check print quality. Simultaneously pull back on the transport chassis and forward on the input hopper. Intended Audience This manual is intended for use by authorized representatives of Datacard who are responsible for the maintenance, service, and pronter of the CP80 and CP80 Plus card printers.

Datacard CP80 ID Card & Driver License Printer

Sequence Of Operation Sequence of Operation Power-on Initialization When the priner is turned on, it begins its initialization routine. Further information about magnetic data formats is located in the Theory of Operation chapter of this manual. Page Remove the two screws that secure the pick motor to the transport chassis, and remove the motor and roller.

Rear Rocker Assembly This procedure is for printers without the magnetic stripe option. Encode and print Click on this button to encode the card and print test graphics on the card. Required Tools and Supplies The following tools and supplies are needed for routine maintenance procedures. Remove the Upper Heater Assembly page from the laminator.

It also allows you to enable or disable the heaters. Testing Motors This dialog box allows you to operate each of the motors in the printer for a specified duration.

Mechanical Inspection Wipe the exterior of the printer with a cloth dampened with a non-abrasive, general purpose cleaning solution.

Remove the bias spring from the card guide. Lower Heater Assembly Make sure the motor wires are connected properly.

DataCard CP80 Plus Service Manual

Page 36 Parity Check A parity check is a method of determining if an error has occurred. Laminator Sensors Laminator Sensors Duplex Exit Sensor The duplex exit sensor is located next to the rear fan and below the duplex interface board. Data Track Locations The positions where data can be recorded on a 3-track stripe are described in the graphic below.

To remove the idler rollers, spread the sidewalls of the flipper, and pull the roller out one side at a time. Page Replacement Notes Snap c8p0 coupler back into the chassis using the four mounting bracket locking tabs.

Security Card Printers : Datacard CP80 Plus

Click on the Save to Power-on Defaults button. Remove the Main Enclosure page and the Swingarm Cover page Testing Motors Testing Motors This dialog box allows you to operate each of the motors in the printer for a specified duration. Page Connect the wire to the heater, and take the slack back out of the wire the loop of wire in the previous photo.

Configuring Custom Track Formats Configuring Custom Track Formats The purpose of the Custom Track Format printrr box is to permit the customer engineer the ability to set up a custom format to meet the specific needs of the end user.